Circular No. 130/2025/TT-BQP amends and supplements certain articles of Circular No. 67/2024/TT-BQP on the procedures for certifying the technical safety quality and environmental protection of imported, produced, and assembled motor vehicles within the scope of management of the Ministry of National Defense. This document specifies the specific deadlines for approving design documents and issuing certificates.
Đối tượng áp dụng
The Motor Vehicle Transport Department under the General Logistics and Technical Department, production and assembly facilities for motor vehicles, and ordering units
Các điểm cốt lõi
- Within seven days from the date of receipt of complete and valid documents, the Director of the Motor Vehicle Transport Department under the General Logistics and Technical Department must approve or recognize the design production and assembly documents (Article 1).
- Within twenty-one days from the date of receipt of complete and valid documents, the Director of the Motor Vehicle Transport Department under the General Logistics and Technical Department must inspect and issue the Certificate of Technical Safety Quality and Environmental Protection for imported or domestically produced motor vehicles (Article 2).
- If the documents are not valid, the Motor Vehicle Transport Department under the General Logistics and Technical Department must notify the relevant unit in writing to supplement the documents within three working days (Articles 1 and 2).
- In cases where the review content is complex, the maximum time does not exceed fourteen days (Article 1).
- If the documents are not valid, the Motor Vehicle Transport Department under the General Logistics and Technical Department must notify the relevant unit in writing to supplement the documents within three working days (Articles 1 and 2).
🌐 Tác động xã hội từ văn bản này
- To enhance the effectiveness of state management over the technical safety quality and environmental protection of motor vehicles.
- Improve the processing time for documents, facilitating production and assembly units.
- Increase requirements for production and assembly facilities in preparing complete documents.
❓ Câu hỏi thường gặp
What is the maximum deadline for approving design production and assembly documents?
Within seven days from the date of receipt of complete and valid documents. In cases where the review content is complex, the maximum time does not exceed fourteen days.
What is the deadline for issuing the Certificate of Technical Safety Quality and Environmental Protection for motor vehicles?
Within twenty-one days from the date of receipt of complete and valid documents.
Toàn văn
|
MINISTRY OF NATIONAL DEFENSE |
SOCIALIST REPUBLIC OF VIET NAM |
|
Number: 130/2025/TT-BQP |
Hanoi, November 25, 2025 |
CIRCULAR
Amending and supplementing certain Articles of Circular No. 67/2024/TT-BQP dated October 14, 2024, issued by the Minister of National Defense, stipulating the procedures and formalities for certifying the technical quality and environmental protection of imported, produced, and assembled motor vehicles within the scope of management of the Ministry of National Defense
On the basis of The Road Traffic Safety Law on June 27, 2024;
Pursuant to Decree No. 01/2022/NĐ-CP dated November 30, 2022, promulgated by the Government, stipulating the functions, tasks, powers, and organizational structure of the Ministry of National Defense; Decree No. 03/2025/NĐ-CP dated February 28, 2025, promulgated by the Government, amending and supplementing certain Articles of Decree No. 01/2022/NĐ-CP dated November 30, 2022, promulgated by the Government, stipulating the functions, tasks, powers, and organizational structure of the Ministry of National Defense;
In accordance with the proposal of the Director of the General Logistics Department - Technical Service;
The Minister of National Defense issues this Circular amending and supplementing certain Articles of Circular No. 67/2024/TT-BQP dated October 14, 2024, issued by the Minister of National Defense, stipulating the procedures and formalities for certifying the technical quality and environmental protection of imported, produced, and assembled motor vehicles within the scope of management of the Ministry of National Defense.
Article 1. Amending and supplementing Point a Clause 3 Article 5 as follows:
"a) Within seven days from the date of receiving complete and valid files, the Director of the Motor Vehicle Transport Department under the General Logistics and Technical Department shall decide to approve or recognize the design production and assembly file according to Model No. 03 attached as an appendix to Circular No. 67/2024/TT-BQP dated October 14, 2024, issued by the Minister of National Defense, stipulating the procedures and formalities for certifying the technical quality and environmental protection of imported, produced, and assembled motor vehicles within the scope of management of the Ministry of National Defense. In cases where the review content is complex, the maximum time shall not exceed fourteen days;
In case the file is incomplete, within three working days, the Motor Vehicle Transport Department under the General Logistics and Technical Department shall notify in writing to the production and assembly facility or the ordering unit to supplement the file;"
Article 2. Amending and supplementing Point a Clause 3 Article 6 as follows:
"a) Within twenty-one days from the date of receiving complete and valid files, the Director of the Motor Vehicle Transport Department under the General Logistics and Technical Department shall inspect and issue the Certificate of Technical Quality and Environmental Protection for imported or domestically produced and assembled motor vehicles;
In case the file is incomplete, within three working days, the Motor Vehicle Transport Department under the General Logistics and Technical Department shall notify in writing to the unit directly assigned by the Ministry of National Defense to purchase or the production and assembly facility or the ordering unit to supplement the file;"
Article 3. Implementation Provisions
This Circular takes effect from November 26, 2025./.
|
Place of Receipt: |
DEPUTY MINISTER |
Văn bản gốc (PDF)
Tải văn bản
Bản đồ quan hệ
Bấm vào một văn bản để mở. Viền đỏ = quan hệ làm thay đổi hiệu lực.
Bản dịch
Văn bản này có sẵn ở các ngôn ngữ sau: